G8 Instructions

G8 Setup & ECU Flashing Guide
Before getting started, please refer to the TD Flasher Instructions if you haven't already completed the initial setup.
Follow the steps below to install the GAP Flasher application on your new G8, connect your device, flash your ECU, and configure your dashboard.
PART 1: Power On & Connect
- Power On the G8
Turn the snowmobile ignition key to the ON position. The G8 display should power on automatically if properly connected.
- Check Your Connections
- Make sure the G8 is connected to Wi-Fi.
- Enable Bluetooth under Settings > Wireless Networks.
- Ensure the snowmobile's battery has sufficient voltage. Connect a battery maintainer if necessary.
IMPORTANT: Maintain a stable battery voltage throughout the ECU flashing process.
PART 2: Install Aptoide
- Open the Browser
- From the G8 applications menu, open the web browser. Tap the address bar (which may display Garmin) and navigate to Google.
- In Google's search bar, enter aptoide gap flasher and select the first relevant result for the Aptoide Android APK download.
- ; Or simply copy and paste this link in your browser:
https://aptoide.en.aptoide.com/app
- Download Aptoide
- Select the Android APK download orange option and be careful not to click the other ones as they are ads.

- If security prompts appear, select Continue to proceed.
- Swipe down from the top of the screen to open notifications.
- Tap the completed Aptoide download.
- Select Install.
Once installation is complete, open the Aptoide application.
PART 3: Install GAP Flasher
- Find GAP Flasher
Still on the Aptoide app, search for GAP Flasher.
- ; Or simply copy and paste this link in your browser:
https://gap-flasher.en.aptoide.com/app
- Install the Application
- Select GAP Flasher and tap the orange Install option, be careful not to click the other ones as they are ads.

- If prompted to allow installation permissions, select Settings.
- Enable the required permission to install the application.
- Return to Aptoide and complete the installation.
- Once installed, open GAP Flasher.
NOTE: Wi-Fi is no longer required once both applications have been installed.
PART 4: Connect to the Flasher
- Locate Your Flasher
In the GAP Flasher application:
- Select Connect Tool or Search for Tool.
- Wait for the available devices window to appear.
- Select your GAP Flasher from the list. (Ensure you snowmobile key is turned ON)
- Establish the Connection
Once connected, the application will display the vehicle's VIN along with an arrow.
- Tap the arrow beside the VIN.
- When asked to connect to the flasher, select Yes.
- You may assign a name to your flasher if desired.
- If prompted to register the flasher, yes if this is your first time using the Flasher, but you could always skip this and do it later.
You should now have access to the flasher dashboard.
PART 5: Flash the ECU
1. Access ECU Flash
From the flasher dashboard:
- Tap the green arrow at the top centre of the screen (iPhone).
- Select the three-line menu icon in the upper-left corner (Android & iPhone).
- Choose ECU Flash.
- On the following screen, locate Tune, found on the second line beneath Online ECU Flash.
- Select Tune.
2. Begin the Flashing Process
- A message indicating the estimated flash duration will appear.
- Select Continue.
- When prompted to write the tune to the ECU, select Yes.
- The application will begin writing the tune to the ECU.
The flash will load into the ECU.
WARNING
DO NOT turn off the ignition, disconnect the flasher, or interfere with either device while the ECU is being flashed.
Interrupting the flashing process may result in an incomplete ECU flash.
3. Complete the Flash
Once the flashing process is complete:
- Select Continue.
- Use the bottom-left back arrow twice to return to the previous menus.
PART 6: Select Your Tune
- View Available Tunes
At the top-left corner of the screen, select Tunes.
If your ECU has multiple tunes available, swipe left or right, or use the navigation arrows, to browse through them.
- Set Your Default Tune
- Locate your preferred tune.
- Select Set Default beneath that tune.
Your default tune will automatically be selected each time you start your snowmobile so long as the TD Flasher remains hooked to the sled.
- Activate a Tune
To activate a specific tune, select it and tap the green arrow in the upper-right corner of the screen.
PART 7: Configure Your Dashboard
1. Customize Your Display
Return to the main Dashboard.
You will see four configurable data fields that illuminate blue when selected.
For the best monitoring experience, Turbo Dynamics recommends displaying:
- Boost
- Throttle Position or AFR is equipped
- RPM
- Engine Temp
To configure each field:
- Tap a dashboard field.
- Select the desired parameter.
- Use the back arrow to return to the dashboard.
- Repeat for the remaining fields.
2. Verify Live Data
To confirm that your dashboard is receiving live data, operate the throttle and observe the Throttle Position reading.
The displayed value should change in response to throttle movement.
Your G8 setup and ECU flashing process are now complete.
If you need assistance, call us at 1-800-549-0246, and have your VIN & Flasher # ready.